![]() ![]() Added Telescope Set SideOfPier() support require OnStep version 5.01 or later. V1.0.15 CommandBool() now handles slewing commands properly. V1.0.16 Telescope enable/disable using :Te# and :Td# only. V1.0.18 Corrected bug that prevented checksum communications from working. V1.0.19 Corrected Description and DriverInfo methods. V1.0.21 Allow OnStepX connection when no mount is present. V1.0.22 Fix for DestinationSideOfPier() and OnStepX. V1.0.23 Fix for get SiteLongitude() and setup dialog UTC Offset. V1.0.24 Allow MoveAxis rates from 0.0 deg/s up to OnStep's MaxRate at the time of connection. V1.0.25 Corrected slew rate display in setup dialog. V1.0.26 Slight change to network port handling including support for persistent command channels 9996, 9997, 9998. V1.0.27 Added per IP connection client servers. V1.0.28 Added per IP connection OnStep base info. V1.0.30 Fix for more flexible Focuser status decode. V1.0.31 Added support for get/set RightAscensionRate and DeclinationRate properties (for OnStepX version 10.13 and later.) The prior stable OnStep ASCOM driver, version 1.50, is available to download here. The current stable OnStep ASCOM driver, version 2.0.6, is available to download here. These new drivers are the result of many many hours of work, please consider making a Donation to help support the developer if you find them useful.įor versions of OnStep prior to release-3.16: These values are usually obtained from an attached BME280 device (otherwise it returns the default TPHD values.) This provides Temperature, Pressure, Humidity, and Dew-Point. The Observing Conditions driver is functional with OnStep version 3.16 or later.It does not support the INTERVALOMETER since that control doesn't logically map to ASCOM Switch capabilities. It also supports switching the DEW_HEATER's on/off. The Switch driver fully supports both SWITCH and ANALOG_OUT Auxiliary Features with OnStep version 4.17 or later.The Rotator driver is only functional with OnStep version 4.17 or later since the command protocol was enhanced in support of this driver.This driver can detect the swapped condition and make sure commands go to the designated focuser (if set to do so, requires OnStep 4.17 or later.) do this) so minimal controls can operate two focusers. OnStep has the ability to "swap" focusers (Android App, SHC, etc. The Focuser driver is functional with OnStep version 3.16 but TCF support (and backlash/deadband) requires version 4.17 or later.The Telescope driver is functional with OnStep version 3.16 or later.Any com (or IP) port (or ports) can be shared among all OnStep ASCOM drivers in this package. These drivers do not require using an ASCOM hub such as POTH for multipule connections.The prior OnStep Telescope and/or Focuser drivers will not be uninstalled automatically by this installer, you can however use Windows "Programs and Features" utility to remove them if you like though they will not interfear with this driver set.Report problems and feel free to uninstall and switch to the prior stable drivers (links below.) If these drivers don't work properly keep in mind they are new and in beta testing.The ASCOM Platform version 6.5 or later should be installed before this driver.The last OnStep ASCOM unified driver (version 1.0.25 supporting Telescope, Focuser, Rotator, Switch and Observing Conditions interfaces) The OnStep ASCOM unified driver (version 1.0.31 supporting Telescope, Focuser, Rotator, Switch and Observing Conditions interfaces)įor OnStep release-3.16 and later, is available to download here. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |